Over 90 Total Lots Up For Auction at One Location - WA 04/08

Agfa DS5302 System Failure

(303)
(47)

CRAIG WAMBURA

Agfa DS5302 System Failure

June 16, 2017 05:53

Dear friends,

I have an Agfa DS5302 printer that has "system failure" at startup.
You can switch the system on/off even with the error.
I have tried to perform a software re-installation but system does not load the CF card at start-up, it just goes to the same error at the point when its checking the drives.
I don't have an emergency_install so I am using the core software package.

Is there another cause for this error or can some one help with a solution

Craig

3 people liked this
Log inor Register

to rate and post a comment

(10)
(1)

Allan Morazan

re: Agfa DS5302 System Failure

June 18, 2017 08:22

Replace themis board.

Log inor Register

to rate and post a comment

(8)

affan rehman

re: re: Agfa DS5302 System Failure

June 24, 2019 10:39

i am facing same problem with agfa 5302 .whats solution

Log inor Register

to rate and post a comment

(10)
(1)

Allan Morazan

re: Agfa DS5302 System Failure

June 18, 2017 08:22

Hard disk failure maybe but less probable

Log inor Register

to rate and post a comment

(16)
(1)

medicalimagecare

re: Agfa DS5302 System Failure

June 18, 2017 08:23

Dear sir
we are freelance engg. of agfa so plz give me your system in team viewer we are trying to load software
our e mail medicalimagecr@gmail.com
whatsapp no +918896046247 , +919999393192

Log inor Register

to rate and post a comment

(9)
(3)

Welson Carreira

re: Agfa DS5302 System Failure

June 19, 2017 10:22

It will probably be necessary to replace the themis/tyndall board, if it is the tyndall board (serial number above 12500) and two green leds are flashing or the red led is direct access, replace the tyndall board.

1 person liked this
Log inor Register

to rate and post a comment

(9)
(3)

Welson Carreira

re: Agfa DS5302 System Failure

June 19, 2017 10:22

Failure of the SYSTEM ERROR means that the operating system can not be loaded, the items that can cause this failure are:
Memory
Themis - Tyndall
Devius - Devils
HD (SCSI or SATA)

Usually the fault is Themis / Tindall.

For equipment with a serial number above 12,500, they will be using the Tyndall card if the 2 green LEDs on the 4 green LEDs that monitor the power supply on the Tyndal card are blinking. The problem is the TYNDALL board, or the red LED is connected directly, you can change the Tyndall board.

1 person liked this
Log inor Register

to rate and post a comment

(31)
(9)

Fedor Uvarov

re: Agfa DS5302 System Failure

June 25, 2017 05:27

The problem consists in bad soldering of CPU. The processor heats up and cooled on which balls it is soldered burst and the contact is lost.
Solution warming up (soldering) of the processor! More than 2 tens printers across Russia were so regenerated already.

1 person liked this
Log inor Register

to rate and post a comment

(303)
(47)

CRAIG WAMBURA

re: re: Agfa DS5302 System Failure

June 26, 2017 10:47

Thank you

Log inor Register

to rate and post a comment

(31)
(9)

Fedor Uvarov

re: re: re: Agfa DS5302 System Failure

June 26, 2017 04:21

Try to solder!
Good luck!

Log inor Register

to rate and post a comment

(8)

Perenlei Besuud

re: re: re: re: Agfa DS5302 System Failure

October 11, 2018 08:09

Hello Fedor, Nice to meet you in Dotmed,I like your opinion for System failure i want to try it my DS5302.Pl contact with me by besuudp@yahoo.com Thanks Besuud from Mongolia

Log inor Register

to rate and post a comment

(8)

Perenlei Besuud

re: re: Agfa DS5302 System Failure

October 11, 2018 08:09

I would like to try your method but in which board .Where is i will do it? Please answer me Жду ответа

Log inor Register

to rate and post a comment

(8)

Perenlei Besuud

re: Agfa DS5302 System Failure

October 11, 2018 08:09

Craig ,Did you solve your problem? I now have same problem like yours.Could you answer by besuudp@yahoo,com Thanks

Log inor Register

to rate and post a comment

(303)
(47)

CRAIG WAMBURA

re: re: Agfa DS5302 System Failure

October 11, 2018 11:04

Contact me craigwambura@outlook.com

Log inor Register

to rate and post a comment

(303)
(47)

CRAIG WAMBURA

re: re: Agfa DS5302 System Failure

October 11, 2018 11:04

I replaced the Themis/Tyndall boards and performed a software upgrade.

Log inor Register

to rate and post a comment

(109)
(15)
(1)

Svilen Popov

re: re: re: Agfa DS5302 System Failure

December 04, 2018 05:58

I have the problem with "system failure' too, but the strange thing is that, when I have this error at boot up - status led on front panel, doesn't lights and Themis board was changed one year ago.
I reinstall software with 5.1.0 and have system failure again.
Is it possible to have defect in themis board again ?
I have only D1 and D11 lights(yellow), when turn on the DS5302

Log inor Register

to rate and post a comment

(303)
(47)

CRAIG WAMBURA

re: re: re: re: Agfa DS5302 System Failure

December 05, 2018 09:26

I would replace the whole assay i.e. Themis/Tyndal...
Can contact me for help at craigwambura@outlook.com

Log inor Register

to rate and post a comment

(8)

affan rehman

re: Agfa DS5302 System Failure

June 24, 2019 10:38

how to resolve this problem . i am facing same problem

Log inor Register

to rate and post a comment

(1)

DIEGO LINS

re: Agfa DS5302 System Failure

June 08, 2023 10:00

You can fix the boad,
In video bellow I show you

Hi,

You can solve this problem with video below.

https://www.youtube.com/watch?v=Ma8xhQu7Htc

Log inor Register

to rate and post a comment

stats
DOTmed text ad

stats
advertisement

Upcoming Auction Events

NorthWest Supply
TIMED
Apr 08, 2024 (99 lots)